Paver Sealing in Melbourne & All of Brevard County, FL
Water-based sealer. Color restoration. Two-coat application. Joint sand stabilization. Done right in one visit — with a written quote before we start.
Why Melbourne Pavers Fade, Shift, and Grow Weeds
Paver driveways, patios, and pool decks across Brevard County share a few common problems that show up within the first 3–5 years of installation. The sun bleaches the color out of the top layer. Joint sand washes away in heavy summer rains, letting weeds take root. Algae and mildew take over shaded sections. Salt spray from the coast works its way into the joints. And by year 5 or 6, pavers that once looked like an investment now look like deferred maintenance.
Proper paver sealing solves all of this in one visit. We clean the pavers thoroughly, re-sand the joints, and apply a water-based sealer that locks the sand in place, enhances the color, and creates a barrier against salt, algae, oil, and UV damage. When it’s done right, a single paver sealing job buys you 2–3 years of looks-brand-new pavers. When it’s done wrong — cheap sealer, skipped prep, one thin coat — the sealer peels, turns hazy, or traps moisture underneath, and you’re looking at a strip-and-reseal job in a year.
We’ve sealed thousands of Brevard driveways. Here’s exactly how we do it.
Our 6-Step Paver Sealing Process
Every paver sealing job we do follows the same six steps. We’ll walk through all of them with you during the on-site estimate so you know exactly what’s happening to your property.
1. On-site estimate and assessment
We come to your property, measure the pavers, check for failed previous sealer, look for damaged or sinking pavers that need attention, and identify any stains that need pre-treatment. You get a written quote with the full scope of work — no add-ons mid-job.
2. Stain pre-treatment
Oil stains, rust from irrigation systems, fertilizer burns, and organic stains all get specific pre-treatments before the main cleaning. Rust responds to oxalic acid. Oil needs a degreaser and dwell time. Algae gets an algicide. Taking 20 extra minutes here means stains come out instead of getting sealed in permanently.
3. Hot-water pressure wash with rotary surface cleaner
We use a rotary surface cleaner (not a wand) for an even, stripe-free clean, paired with hot water that cuts through embedded grime the way cold water can’t. For pavers with failed solvent-based sealer, this step is preceded by a citrus-based stripper application and a dwell period — the peelings come off cleanly and we dispose of them properly.
4. 24–48 hour dry period
Pavers need to be completely dry before sealer goes on. Sealing wet pavers traps moisture under the sealer and turns it milky within weeks. We always come back on a separate day for steps 5 and 6, which is why paver sealing is a two-day process.
5. Joint sand re-sanding
We use polymeric joint sand (not regular masonry sand) swept into every joint and activated with a light mist. Polymeric sand hardens slightly and prevents weeds from rooting, which is the #1 failure point for un-resanded paver jobs in Florida.
6. Two-coat sealer application
Two full coats of water-based sealer, applied with a low-pressure sprayer for even coverage and back-rolled into the paver surface. Color tinting applied at this stage if you’ve chosen it. Caution tape goes up for 48 hours of cure time — walkable at 3 hours, drivable at 24.
Why We Only Use Water-Based Sealer
There are two main types of paver sealer on the market: water-based and solvent-based. In Florida’s climate, only one of them holds up. Here’s the difference:
| Feature | Water-Based (what we use) | Solvent-Based (we don’t) |
|---|---|---|
| Breathability | Allows moisture to escape from paver base | Traps moisture — turns hazy/milky in FL |
| VOCs | Low VOC, safer for landscaping and pets | High VOC, strong odor |
| Florida longevity | 2–3 years, fades gracefully | Often fails within 12–18 months |
| Slip resistance | Safe wet or dry when applied correctly | Often slippery when wet — a pool deck hazard |
| When it fails | Fades evenly, easy to refresh | Peels in sheets — requires full strip |
If you’ve been told by another contractor that solvent-based sealer is “higher quality” or “longer lasting,” ask them specifically about Florida’s water table. The answer matters. The reason you see so many hazy, milky-white paver driveways in Melbourne, Palm Bay, and Cocoa is that solvent-based sealer was used in a climate it can’t survive in.
What Does Paver Sealing Cost in Brevard County?
We can’t give you an exact number without seeing your pavers — square footage, condition, and whether there’s failed sealer that needs stripping all change the price. But here’s a transparent range so you know what to budget for before you even call:
| Project Size | Typical Range | Example |
|---|---|---|
| Small (under 400 sq ft) | $400 – $700 | Small back patio or walkway |
| Medium (400–800 sq ft) | $700 – $1,400 | Standard driveway or large patio |
| Large (800–1,500 sq ft) | $1,400 – $2,500 | Long driveway + pool deck or patio combo |
| Estate (1,500+ sq ft) | $2,500+ | Waterfront home with full hardscape |
These ranges assume pavers in reasonable condition. If your pavers have failed solvent-based sealer that has to be stripped first, add roughly $300–$700 to the base price depending on square footage. Color tinting is usually included at no additional charge — we just match the sealer to the tint you pick during the estimate.
If you see a quote significantly lower than these ranges, ask what’s being skipped. The two most common shortcuts in Brevard paver sealing are (1) a single thin coat instead of two full coats and (2) skipped joint sand re-sanding. Both save the contractor time; both cost you 6–12 months of sealer life.
We Seal Every Common Brevard Paver Type
Brick Pavers
The most common paver type in Brevard driveways and patios. We seal every major manufacturer (Belgard, Tremron, Pavestone) and every pattern. Color restoration works especially well on brick — older faded pavers can look brand new after tinted sealer.
Concrete Pavers
Concrete pavers are more porous than brick and benefit from sealing even more — unsealed concrete pavers absorb stains and fade faster than any other paver type in Florida sun. Two coats of water-based sealer make a noticeable difference immediately.
Travertine
Travertine is a porous natural stone common around Brevard pool decks. It needs to be sealed every 1–2 years — more frequently than brick or concrete — because water, chlorine, and salt can all penetrate and cause long-term damage. We use travertine-safe sealer that stays slip-resistant around pools.
Flagstone & Natural Stone
For coral, flagstone, and other natural stone patios common in older Brevard builds, we use natural-stone-specific sealers that enhance the color without the plasticky look some paver sealers give to stone.
No Mystery Line Items
Here’s exactly what’s included in every paver sealing quote we give, and what counts as an extra charge. You’ll see the full itemized list in writing before you sign anything.
✓ Included in every paver sealing quote
- On-site estimate
- Pre-treatment of stains
- Hot-water pressure wash with rotary surface cleaner
- Polymeric joint sand re-sanding
- Two full coats of water-based sealer
- Color tinting (optional, no extra charge)
- Landscaping protection and cleanup
- Final walkthrough with homeowner
+ Extra charges (quoted upfront)
- Failed sealer stripping (+$300–$700)
- Replacement of broken pavers (quoted per paver)
- Re-leveling sinking pavers (quoted per area)
- Anti-slip additive for pool decks (optional)
Frequently Asked Questions
What type of sealer do you use on pavers?
We use water-based paver sealers exclusively. Water-based products allow the pavers to breathe, preventing the moisture entrapment that turns solvent-based sealers milky white in Florida’s high water table. They’re also low-VOC and safer around Florida landscaping.
Do I need to have my pavers cleaned before sealing?
Yes — cleaning is part of every sealing job. We pressure wash with a rotary surface cleaner, treat any algae or mold with algicide, re-sand the joints, let everything dry for 24 to 48 hours, then apply two coats of sealer. Skipping the clean step seals the dirt in permanently.
Can you seal travertine pavers around my pool?
Yes. Travertine is porous and should be sealed every 1 to 2 years, especially around pool decks in Florida. We use sealers specifically formulated for travertine that don’t make the surface slippery when wet.
What if my pavers have old peeling sealer?
We strip it before resealing. Failed solvent-based sealer requires a citrus-based stripper, a hot-water pressure wash to remove the residue, and careful disposal of the peelings. It’s a full extra step but the only way to get a clean bond on the new coat.
Do you tint the sealer to restore faded paver color?
Yes. We offer tinted sealers that restore faded pavers to their original color. This is a popular service for homes in Brevard where 10+ years of UV exposure has bleached the top layer of the pavers.
Ready for a free paver sealing quote?
We service all of Brevard County. Most paver sealing jobs can be scheduled 1–2 weeks out. Call (321) 432-4340 or fill out our contact form and we’ll reach out the same business day.